REVISION R
QTH-XXX-XX-X-D-DP-XXX
OPTION
No OF POSITIONS
-A: ALIGNMENT PINS
-020, -040, -060,
***-080, ***-100
(PER ROW)
(SEE FIGS 1 & 3, SHEET 2)
-LC: LOCKING CLIPS
*
(USE LC-08-TM-01, SEE FIG. 1)
-K: POLYIMIDE FILM (USE K-500-300)
(AVAILABLE ON -01 THRU -04 &
-09 AND -10 ONLY)(SEE FIG. 2, SHEET 2)
-TR: TAPE & REEL (60 POS MAX)
(40 POS MAX FOR -GP OPTION)
-GP: GUIDE POSTS OPTION
C3
***SEE NOTE 11
(No OF POSITIONS / 20) x .7875[20.003]
LEAD STYLE
-01: .1680[4.267]
DO NOT
SCALE FROM
THIS PRINT
.7875 20.003 REF
*-02: .2861[7.264]
*-03: .4042[10.267]
*-04: .6000[15.240]
*-05: .7180[18.237]
*-06: .8360[21.234]
*-07: .9542[24.237]
*-08: 1.1511[29.238]
*-09: .5224[13.269]
*-10: .5618[14.269]
.551 14.00 REF
**
01
(AVAILABLE ON -01 & **-02 ONLY)
(USE QTH-30-XX-D-XX-GP)
(SEE FIG. 7, SHEET 4)
-RT1: RETENTION OPTION (SEE FIG. 8, SHEET 4)
(ONLY AVAILABLE ON -01 LEAD STYLE)
(MUST USE -A OPTION)
.155 3.94
REF
.235 5.97
REF
(USE QTH-30-01-D-XX-A-RT1 & T-1R36-01-F)
(NOT AVAILABLE WITH -LC OR -GP)
(NOT AVAILABLE ON -080 & -100 POS)
02
PLATING SPECIFICATION
.644 16.36 REF
DIFFERENTIAL PAIRS
-F: FLASH SELECTIVE GOLD
(USE T-1SXX-XX-F & T-1GXX-XX-F)
(SEE NOTE 7)
.0197 0.500
REF
.008 0.20 REF
ROW SPECIFICATION
-D: DOUBLE (USE QTH-30-01-D-XX)
No OF BANKS
FIG. 1
.0591 1.500
REF
-L: LIGHT SELECTIVE GOLD
(USE T-1SXX-XX-L & T-1GXX-XX-L)
-H: HEAVY GOLD
QTH-090-01-X-D-LC SHOWN
* = RELEASED FOR ASO ONLY
(APPLICATION SPECIFIC ORDER)
** = -02 LEAD STYLE NOT RELEASED
FOR PRODUCTION
(USE T-1SXX-XX-H & T-1GXX-XX-G)
"A"
QTH-30-XX-D-XX
T-1SXX-XX-X
.055 1.40
C1
.003[.08]
.001[.03]
C2
"A"
.098 2.49 REF
"B" REF
(SEE NOTE 5 & 8)
SEE TABLE 2
(SEE NOTE 8)
T-1G1-XX-X
SEE NOTE 10
.037 0.94 REF
.0375 0.953 REF
.015 0.38 REF
"A"
LC-08-TM-01
.745 18.92 REF
.010 0.25 REF
.280 7.11 REF
(((No OF POSITIONS / 20) x .7875[2.003]) - .060[1.52]) .003[.08]
SECTION "A"-"A"
NOTES:
-LC: LOCKING CLIP OPTION SHOWN
C
1.
REPRESENTS A CRITICAL DIMENSION.
2. MINIMUM PUSHOUT FORCE: 6 OZ FOR –01 & -02, 8 OZ FOR –03 THRU –09.
3. MINIMUM GROUND PLANE RETENTION: 1 LB.
QTH-30-XX-D-XX-A
4. PARTS TO BE MOLDED TO POSITION.
5. MAXIMUM VARIANCE OF .002[.05]. APPLIES TO SIGNAL OR GROUNDS
INDEPENDENT OF THE GROUND OR SIGNAL PINS RESPECTIVELY.
6. LEAD STYLES -03 THRU -08: TOP BODY (QTH) CANNOT HAVE -A OPTION.
7. -L PLATING CAN BE SUBSTITUTED FOR -F PLATING.
.037 0.95
REF
-G PLATED GROUND PLANE CAN BE SUSTITUTED FOR –F PLATED GROUND PLANE.
8. GROUND PLANE PRESS HEIGHT MUST BE .003 [.07] LESS THAN THE MAXIMUM
HEIGHT OR .002[.03] GREATER THAN THE MINIMUM HEIGHT OF SIGNAL PIN.
9. T-1R36 RETENTION TO BODY TO BE 1.0 LBF.
.035 0.89
REF
((No OF POSITIONS / 20) x .7875[2.003]) - .060[1.52] REF
10. CUT OFF BURR NOT TO EXCEED .003 IN ANY DIRECTION, BURR PLUS
TAB HEIGHT NOT TO EXCEED .006.
.0375 0.953 REF
-A: ALIGNMENT PIN OPTION
11. FOR NEW APPLICATIONS REQUIRING THESE POSITIONS, PLEASE CONTACT
SAMTEC INTERCONNECT PROCESSING GROUP.
[STYLE -01 & -02]
UNLESS OTHERWISE SPECIFIED,
PROPRIETARY NOTE
DIMENSIONS ARE IN INCHES.
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
TOLERANCES ARE:
DECIMALS
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
ANGLES
2
.XX: .01[.3]
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail: info@SAMTEC.com code: 55322
DESCRIPTION:
.XXX: .005[.13]
.XXXX: .0020[.051]
SHEET SCALE: 1.75:1
DO NOT SCALE DRAWING
MATERIAL:
.5mm DIFFERENTIAL PAIRS TERMINAL ASSEMBLY
DWG.
INSULATOR: LCP, COLOR: BLACK
TERMINAL & GROUND PLANE: PHOS BRONZE
QNTOH. -XXX-XX-X-D-DP-XXX
BY:
KEVIN B
6/14/2000
SHEET 1 OF 4
c:\enterprisevault\DWG\MISC\MKTG\QTH-XXX-XX-X-D-DP-XXX-MKT.SLDDRW
