ASO ONLY (APPLICATION SPECIFIC ORDER)
REVISION N
QTS-XXX-XX-XXX-D-DP-XX
No OF POSITIONS
DO NOT
SCALE FROM
THIS PRINT
OPTION
-016, -032, -048,
**-064, **-080
(PER ROW)
-A: ALIGNMENT PINS (SEE FIG. 2)
(USE QTS-25-01-D-XX-A)
-LC: LOCKING CLIPS (SEE FIG. 1, NOTE 15)
(USE LC-08-TM-01)
(No OF POS/16) x .7875[20.003] REF
7 EQ SPACES @ .075[1.91]
.7875 20.003 REF
**SEE NOTE 14
-K: POLYIMIDE FILM PAD OPTION
(SEE FIG. 3, SHT. 2)
LEAD STYLE
-01: .1680[4.267]
-02: .2861[7.264]
-03: .4042[1.123]
-04: .6000[15.240]
-05: .7180[18.237]
-06: .8360[21.234]
(USE K-500-300)
-TR: TAPE & REEL OPTION
(48 POS MAX)
01
*
*
.235 5.97
REF
.155 3.94 REF
-DP: DIFFERENTIAL PAIRS
ROW SPECIFICATION
PLATING SPECIFICATION
-F: FLASH SELECTIVE GOLD, MATTE TIN TAILS
(USE T-1SXX-XX-F & T-1G1-XX-F)(SEE NOTE 11)
-L: LIGHT SELECTIVE GOLD, MATTE TIN TAILS
(USE T-1SXX-XX-L & T-1G1-XX-L)
-H: HEAVY GOLD
(USE T-1SXX-XX-H & T-1G1-XX-G)
-STL: HEAVY SELECTIVE GOLD, TIN LEAD TAILS
(USE T-1SXX-XX-STL & T-1G1-XX-STL)
-FTL: FLASH SELECTIVE GOLD, TIN LEAD TAILS
(USE T-1SXX-XX-FTL & T-1G1-XX-FTL)
-D: DOUBLE
(SEE TABLE 3)
02
.644 16.36 REF
.0325 0.826 REF
= SEE SHEET 3
* = NOT ENGINEERING APPROVED
.008 0.20 REF
.075 1.91 REF
.025 0.64 REF
'A'
C2
.003[.08]
.001[.03]
"A"
QTS-25-01-D-XX
T-1G1-XX-XXX
(SEE NOTES 9, 10 & 12)
T-1S56-XX-XXX
"A"
"A"
.055 1.40
C3
"B" REF
SEE TABLE 2
(SEE NOTES 10 & 12)
.280 7.11 REF
.745 18.92 REF
LC-08-TM-01
.010 0.25 REF
.037 0.94 REF
.0375 0.953 REF
.015 0.38 REF
({(No OF POS/16) x .7875[20.003]} - .060[1.52]) .003[.08]
2 MAX SWAY
.006 0.15
REF
SECTION "A"-"A"
FIG. 1
NOTES:
(TYP)
C
1.
REPRESENTS A CRITICAL DIMENSION.
QTS-048-01-XXX-D-DP-LC SHOWN
2. NOTE WAS DELETED.
3. NOTE WAS DELETED.
QTS-25-01-D-XX-A
.0375 0.953
REF
4. MINIMUM TERMINAL RETENTION: 5 OZ.
5. MINIMUM GROUND PLANE RETENTION: 1 LB.
6. NOTE WAS DELETED.
DETAIL 'A'
SCALE 6 : 1
7. PARTS TO BE MOLDED TO POSITION.
8. NOTE WAS DELETED.
9. MAXIMUM VARIANCE OF .002[.05].
{(No OF POS/16) x .7875[20.003]} - .060[1.52] REF
.035 0.89
REF
10. DIMENSION APPLIES TO TERMINALS AND GROUND PLANES INDEPENDENT OF
THE GROUND PLANE OR TERMINAL RESPECTIVELY.
11. -L PLATING CAN BE SUBSTITUTED FOR -F PLATING.
.0375 0.953
REF
FIG. 2
-A: ALIGNMENT PIN OPTION SHOWN
12. GROUND PLANE PRESS HEIGHT MUST BE .003[.08] LESS THAN THE MAX
HEIGHT OR .001[.03] GREATER THAN THE MINIMUM HEIGHT OF THE TERMINALS.
13. LEAD STYLES -03 THRU -06: TOP BODY (QTS) CANNOT HAVE -A OPTION.
14. FOR NEW APPLICATIONS REQUIRING THESE POSITIONS, PLEASE CONTACT
SAMTEC INTERCONNECT PROCESSING GROUP.
15. DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED, THE –LC OPTION IS
NOT COMPATIBLE WITH AUTO PLACEMENT. SAMTEC RECOMMENDS MANUAL
PLACEMENT FOR ALL ASSEMBLIES WITH THE –LC OPTION."
UNLESS OTHERWISE SPECIFIED,
PROPRIETARY NOTE
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DECIMALS
ANGLES
2
.XX: .01[.3]
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail: info@SAMTEC.com code: 55322
.XXX: .005[.13]
.XXXX: .0020[.051]
SHEET SCALE: 1.5:1
MATERIAL:
DO NOT SCALE DRAWING
DESCRIPTION:
.635mm DIFFERENTIAL PAIRS HS TERMINAL ASSEMBLY
INSULATOR: LCP, COLOR: BLACK
TERMINAL & GROUND PLANE: PHOS BRONZE
DWG. NO.
N
QTS-XXX-XX-XXX-D-DP-XX
BY:
KEVIN B
07/07/2000 SHEET 1 OF 3
c:\enterprisevault\DWG\MISC\MKTG\QTS-XXX-XX-XXX-D-DP-XX-MKT.SLDDRW
