QTH-XXX-XX-X-D-XXX
REVISION BA
No OF POSITIONS
OPTION
-LC: LOCKING CLIPS
-030, -060, -090,
(USE LC-08-TM-01)
*-120, *-150
-A: ALIGNMENT PINS
(PER ROW)
* (SEE NOTE 11)
DO NOT
SCALE FROM
THIS PRINT
(USE QTH-30-XX-D-XX-A FOR -01 & -02)
(FOR -03 THRU -10 SEE TABLE 4)
-K: POLYIMIDE FILM (USE K-DOT-.276-.375-.005)
(AVAILABLE ON -01 THRU -04, -09 & -10 ONLY)
(SEE FIG 2, SHEET 2)
C3
LEAD STYLE
(No OF POSITIONS / 30) x .7875[20.003]
-01: .1680[4.267]
-02: .2861[7.264]
-03: .4043[10.269]
-04: .6001[15.246]
-05: .7181[18.240]
-06: .8361[21.237]
-07: .9542[24.237]
-08: 1.1511[29.238]
-09: .5224[13.269]
-10: .5618[14.269]
.788 20.0 REF
-TR: TAPE & REEL (90 POS MAX)
(60 POS MAX W/ -GP OPTION)
(N/A ON -05 THRU -08)
29 EQ SPACES @
.0197[.500]
-GP: GUIDE POSTS
.235 5.97
REF
(AVAILABLE ON -01 & -02 ONLY)
(USE QTH-30-XX-D-XX-X-GP)
(SEE FIG 7, SHEET 4)
01
-FL: FRICTION LOCKS (SEE FIG 8, SHEET 4)
(NOT AVAILABLE WITH -GP)
= SEE TABLE 4
-RT1: RETENTION OPTION (SEE FIG 9, SHEET 5)
(ONLY AVAILABLE ON -01 LEAD STYLE)
(MUST USE -A OPTION)
.155 3.9 REF
(SEE NOTE 12)
PLATING SPECIFICATION
-F: FLASH SELECTIVE GOLD WITH MATTE TIN TAILS
(USE T-1SXX-XX-F & T-1GXX-XX-F)
(SEE NOTE 7)
-L: LIGHT SELECTIVE GOLD WITH MATTE TIN TAILS
(USE T-1SXX-XX-L & T-1GXX-XX-L)
-H: HEAVY GOLD WITH FLASH GOLD TAILS
(USE T-1SXX-XX-H & T-1GXX-XX-G)
-C: ELECTRO-POLISHED SELECTIVE
(USE T-1SXX-XX-C, T-1GXX-XX-L)
(USE QTH-30-01-D-XX-A-RT1 & T-1R36-01-F)
(NOT AVAILABLE WITH -LC, -GP, OR -FL)
**-L: LATCHING OPTION (SEE FIG 10, SHT 6)
(ONLY AVAILABLE ON -01 LEAD STYLE)
(USE **QTH-30-01-D-XX-L)
02
(NOT AVAILABLE WITH -LC, -GP, -FL, OR -RT1)
.644 16.4 REF
.047 1.19 REF
.008 0.2 REF
**NOT TOOLED
ROW SPECIFICATION
-D: DOUBLE (USE QTH-30-XX-D-XX
& QTHH-30-XX-D-XX)
FIG 1
QTH-090-01-X-D-LC SHOWN
.003[.08] C1
"A"
T-1SXX-XX-X
(SEE TABLE 1)
QTH-30-XX-D-XX
.002[.03]
"A"
(SEE NOTE 5 & 8)
C2
.055 1.40
"B" REF
SEE TABLE 2
.098 2.49 REF
(SEE NOTE 10)
(SEE NOTE 8)
.015 0.4 REF
"A"
T-1G1-XX-X
LC-08-TM-01
.745 18.9 REF
.010 0.3 REF
.038 1.0 REF
2
MAX SWAY
(TYP)
.037 0.9 REF
-LC: LOCKING CLIP OPTION SHOWN
.280 7.11 REF
QTH-30-XX-D-XX-A
SECTION "A"-"A"
R
.037 0.95
REF
((No OF POSITIONS / 30) x .7875[20.003]) - .060[1.52] REF
.035 0.89
REF
-A: ALIGNMENT PIN OPTION
.038 1.0 REF
[STYLE -01 & -02]
NOTES:
C
1.
REPRESENTS A CRITICAL DIMENSION.
2. MINIMUM PUSHOUT FORCE: 6 OZ FOR –01 & -02, 8 OZ FOR –03 THRU –10.
3. MINIMUM GROUND PLANE RETENTION: 1 LB.
4. PARTS TO BE MOLDED TO POSITION.
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
PROPRIETARY NOTE
5. MAXIMUM VARIANCE OF .002[.05]. APPLIES TO SIGNAL OR GROUNDS
INDEPENDENT OF THE GROUND OR SIGNAL PINS RESPECTIVELY.
6. LEAD STYLES -03 THRU -10: TOP BODY (QTH) CANNOT HAVE -A OPTION.
7. -L PLATING CAN BE SUBSTITUTED FOR -F PLATING.
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
TOLERANCES ARE:
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DECIMALS
ANGLES
2
.XX: .01[.3]
.XXX: .005[.13]
.XXXX: .0020[.051]
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail info@SAMTEC.com code 55322
DESCRIPTION:
8. GROUND PLANE PRESS HEIGHT MUST BE .003 [.07] LESS THAN THE MAXIMUM HEIGHT
OR .002[.03] GREATER THAN THE MINIMUM HEIGHT OF SIGNAL PIN.
9. T-1R36 RETENTION TO BODY TO BE 1.0 LBF.
SHEET SCALE: 1:0.571429
DO NOT SCALE DRAWING
MATERIAL:
INSULATOR: LCP, COLOR: BLACK, FLAMMABILITY RATING: UL94VO
TERMINAL & GROUND PLANE: PHOS BRONZE
.5mm DOUBLE ROW HS TERMINAL ASSEMBLY
DWG. NO.
10. CUT OFF BURR NOT TO EXCEED .003 [.07] IN ANY DIRECTION, BURR PLUS TAB
HEIGHT NOT TO EXCEED .006 [.15].
11. FOR NEW APPLICATIONS REQUIRING THESE POSITIONS, PLEASE CONTACT SAMTEC
INTERCONNECT PROCESSING GROUP.
QTH-XXX-XX-X-D-XXX
12. MINIMUM ROW TO ROW IS .152, PIN CAN EXTEND PAST WALL .003 MAX.
DEAN P
09-14-2010
SHEET 1 OF 6
BY:
F:\DWG\MISC\MKTG\QTH-XXX-XX-X-D-XXX-MKT.SLDDRW
