请登录

免费注册

购物车 0

上传BOM

产品分类

找货询价

QQ咨询

会员中心

购物车

技术支持

售后咨询

5T93GL02PGI8

型号：

5T93GL02PGI8

品牌：

IDT[ INTEGRATED DEVICE TECHNOLOGY ]

页数：

14 页

PDF大小：

145 K

下载PDF手册

IDT5T93GL02

INDUSTRIALTEMPERATURERANGE

2.5VLVDS1:2GLITCHLESSCLOCKBUFFERTERABUFFERII

2.5V LVDS 1:2 GLITCHLESS

IDT5T93GL02

CLOCK BUFFER

TERABUFFER™ II

DESCRIPTION:

FEATURES:

TheIDT5T93GL022.5Vdifferentialclockbufferisauser-selectablediffer-

• Guaranteed Low Skew < 50ps (max)

• Very low duty cycle distortion < 100ps (max)

• High speed propagation delay < 2.2ns (max)

• Up to 450MHz operation

entialinputtotwoLVDSoutputs. ThefanoutfromadifferentialinputtotwoLVDS

outputsreducesloadingontheprecedingdriverandprovidesanefficientclock

distributionnetwork. TheIDT5T93GL02canactasatranslatorfromadifferential

HSTL, eHSTL, LVEPECL (2.5V), LVPECL (3.3V), CML, or LVDS input to

LVDS outputs. A single-ended 3.3V / 2.5V LVTTL input can also be used to

translatetoLVDSoutputs. Theredundantinputcapabilityallowsforaglitchless

change-over from a primary clock source to a secondary clock source up to

450MHz. SelectableinputsarecontrolledbySEL. Duringtheswitchover,the

outputwilldisablelowforuptothreeclockcyclesofthepreviously-selectedinput

clock. The outputs will remain low for up to three clock cycles of the newly-

selectedclock,afterwhichtheoutputswillstartfromthenewly-selectedinput.

AFSELpinhasbeenimplementedtocontroltheswitchoverincaseswherea

clocksourceisabsentorisdriventoDClevelsbelowtheminimumspecifications.

The IDT5T93GL02 outputs can be asynchronously enabled/disabled.

Whendisabled,theoutputswilldrivetothevalueselectedbytheGLpin. Multiple

power and grounds reduce noise.

• Selectable inputs

• Hot insertable and over-voltage tolerant inputs

• 3.3V / 2.5V LVTTL, HSTL, eHSTL, LVEPECL (2.5V), LVPECL (3.3V),

CML, or LVDS input interface

• Selectable differential inputs to two LVDS outputs

• Power-down mode

• 2.5V VDD

• Available in TSSOP package

APPLICATIONS:

• Clock distribution

FUNCTIONALBLOCKDIAGRAM

OUTPUT

CONTROL

OUTPUT

CONTROL

SEL

FSEL

TheIDTlogoisaregisteredtrademarkofIntegratedDeviceTechnology,Inc.

INDUSTRIAL TEMPERATURE RANGE

JANUARY 2007

DSC 6759/6

IDT5T93GL02

2.5VLVDS1:2GLITCHLESSCLOCKBUFFERTERABUFFERII

INDUSTRIALTEMPERATURERANGE

ABSOLUTEMAXIMUMRATINGS⁽¹⁾

PINCONFIGURATION

Symbol

VDD

Description

Max

–0.5 to +3.6

–0.5 to VDD +0.5

–65 to +150

150

Unit

Power Supply Voltage

Input Voltage

GND

A²

Output Voltage⁽²⁾

Storage Temperature

Junction Temperature

TSTG

°C

GND

V^DD

FSEL

VDD

Q¹

NOTES:

1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause

permanent damage to the device. This is a stress rating only and functional operation

of the device at these or any other conditions above those indicated in the operational

sections of this specification is not implied. Exposure to absolute maximum rating

conditions for extended periods may affect reliability.

2. Not to exceed 3.6V.

V^DD

VDD

SEL

CAPACITANCE⁽¹⁾(TA = +25°C, F = 1.0MHz)

A¹

GND

Symbol

Parameter

Min

Typ.

Max.

Unit

CIN

Input Capacitance

—

NOTE:

1. This parameter is measured at characterization but not tested

TSSOP

TOP VIEW

RECOMMENDEDOPERATINGRANGE

Symbol

Description

Min.

–40

2.3

Typ.

+25

2.5

Max.

+85

2.7

Unit

°C

AmbientOperatingTemperature

InternalPowerSupplyVoltage

VDD

IDT5T93GL02

INDUSTRIALTEMPERATURERANGE

2.5VLVDS1:2GLITCHLESSCLOCKBUFFERTERABUFFERII

PINDESCRIPTION

Symbol

A[1:2]

I/O

Type

Description

Adjustable^(1,4)Clockinput. A[1:2] isthe"true"sideofthedifferentialclockinput.

Adjustable^(1,4)Complementaryclockinputs. A[1:2] isthecomplementarysideofA[1:2]. ForLVTTLsingle-endedoperation, A[1:2] shouldbesettothe

A^[1:2]

desiredtogglevoltageforA[1:2]:

3.3V LVTTL VREF = 1650mV

2.5V LVTTL VREF = 1250mV

LVTTL

GatecontrolfordifferentialoutputsQ1 andQ1 throughQ2 and Q2. WhenGisLOW, thedifferentialoutputsareactive. WhenGis

HIGH,thedifferentialoutputsareasynchronouslydriventotheleveldesignatedbyGL⁽²⁾.

Specifies output disable level. If HIGH, "true" outputs disable HIGH and "complementary" outputs disable LOW. If LOW, "true"

outputsdisableLOWand"complementary"outputsdisableHIGH.

SEL

LVDS

LVTTL

Clockoutputs

Complementaryclockoutputs

Reference clock select. When LOW, selects A2 and A2. When HIGH, selects A1 and A1.

Power-down control. Shuts off entire chip. If LOW, the device goes into low power mode. Inputs and outputs are disabled. Both

"true" and "complementary" outputs will pull to VDD. Set HIGH for normal operation.⁽³⁾

FSEL

VDD

LVTTL

PWR

At a rising edge, FSEL forces select to the input designated by SEL. Set LOW for normal operation.

Power supply for the device core and inputs

Ground

GND

NOTES:

1. Inputs are capable of translating the following interface standards:

Single-ended 3.3V and 2.5V LVTTL levels

Differential HSTL and eHSTL levels

Differential LVEPECL (2.5V) and LVPECL (3.3V) levels

Differential LVDS levels

Differential CML levels

2. Because the gate controls are asynchronous, runt pulses are possible. It is the user's responsibility to either time the gate control signals to minimize the possibility of runt

pulses or be able to tolerate them in down stream circuitry.

3. It is recommended that the outputs be disabled before entering power-down mode. It is also recommended that the outputs remain disabled until the device completes power-

up after asserting PD.

4. The user must take precautions with any differential input interface standard being used in order to prevent instability when there is no input signal.

IDT5T93GL02

2.5VLVDS1:2GLITCHLESSCLOCKBUFFERTERABUFFERII

INDUSTRIALTEMPERATURERANGE

DCELECTRICALCHARACTERISTICSOVERRECOMMENDEDOPERATING

RANGEFORLVTTL⁽¹⁾

Symbol

Parameter

Test Conditions

Min.

Typ.⁽²⁾

Max

Unit

InputCharacteristics

IIH

IIL

Input HIGH Current

VDD = 2.7V

—

±5

μA

InputLOWCurrent

VDD = 2.7V

VIK

ClampDiodeVoltage

DCInputVoltage

VDD = 2.3V, IIN = -18mA

—

- 0.7

- 1.2

+3.6

—

VIN

VIH

VIL

- 0.3

1.7

—

DC Input HIGH

DC Input LOW

0.7

VTHI

V^REF

DCInputThresholdCrossingVoltage

Single-EndedReferenceVoltage⁽³⁾

VDD/2

1.65

3.3VLVTTL

2.5VLVTTL

—

1.25

NOTES:

1. See RECOMMENDED OPERATING RANGE table.

2. Typical values are at V^DD= 2.5V, +25°C ambient.

3. For A[1:2] single-ended operation, A[1:2] is tied to a DC reference voltage.

DCELECTRICALCHARACTERISTICSOVERRECOMMENDEDOPERATING

RANGEFORDIFFERENTIALINPUTS⁽¹⁾

Symbol

Parameter

Test Conditions

Min.

Typ.⁽⁴⁾

Max

Unit

InputCharacteristics

IIH

IIL

Input HIGH Current

VDD = 2.7V

—

±5

μA

InputLOWCurrent

VDD = 2.7V

VIK

VIN

VDIF

VCM

ClampDiodeVoltage

DCInputVoltage

DCDifferentialVoltage⁽²⁾

DC Common Mode Input Voltage⁽³⁾

VDD = 2.3V, IIN = -18mA

—

- 0.7

- 1.2

+3.6

—

- 0.3

0.1

0.05

VDD

NOTES:

1. See RECOMMENDED OPERATING RANGE table.

2. VDIF specifies the minimum input differential voltage (VTR - VCP) required for switching where VTR is the "true" input level and VCP is the "complement" input level. The DC differential

voltage must be maintained to guarantee retaining the existing HIGH or LOW input. The AC differential voltage must be achieved to guarantee switching to a new state.

3. VCM specifies the maximum allowable range of (VTR + VCP) /2.

4. Typical values are at VDD = 2.5V, +25°C ambient.

DCELECTRICALCHARACTERISTICSOVERRECOMMENDEDOPERATING

RANGE FOR LVDS⁽¹⁾

Symbol

Parameter

Test Conditions

Min.

Typ.⁽²⁾

Max

Unit

OutputCharacteristics

VOT(+)

VOT(-)

ΔVOT

VOS

DifferentialOutputVoltagefortheTrueBinaryState

DifferentialOutputVoltagefortheFalseBinaryState

ChangeinVOT BetweenComplementaryOutputStates

OutputCommonModeVoltage(OffsetVoltage)

ChangeinVOS BetweenComplementaryOutputStates

OutputsShortCircuitCurrent

247

—

1.2

—

454

1.125

—

1.375

ΔVOS

IOS

VOUT + and VOUT - = 0V

VOUT + = VOUT -

—

I^OSD

DifferentialOutputsShortCircuitCurrent

—

NOTES:

1. See RECOMMENDED OPERATING RANGE table.

2. Typical values are at VDD = 2.5V, +25°C ambient.

IDT5T93GL02

INDUSTRIALTEMPERATURERANGE

2.5VLVDS1:2GLITCHLESSCLOCKBUFFERTERABUFFERII

DIFFERENTIAL INPUT AC TEST CONDITIONS FOR HSTL

Symbol

VDIF

Parameter

Value

Units

InputSignalSwing⁽¹⁾

DifferentialInputSignalCrossingPoint⁽²⁾

750

Duty Cycle

VTHI

t^R, tF

InputTimingMeasurementReferenceLevel⁽³⁾

InputSignalEdgeRate⁽⁴⁾

CrossingPoint

V/ns

NOTES:

1. The 1V peak-to-peak input pulse level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the V^DIF(AC)

specification under actual use conditions.

2. A 750mV crossing point level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the V^Xspecification under

actual use conditions.

3. In all cases, input waveform timing is marked at the differential cross-point of the input signals.

4. The input signal edge rate of 2V/ns or greater is to be maintained in the 20% to 80% range of the input waveform.

DIFFERENTIAL INPUT AC TEST CONDITIONS FOR eHSTL

Symbol

VDIF

Parameter

Value

Units

InputSignalSwing⁽¹⁾

DifferentialInputSignalCrossingPoint⁽²⁾

900

Duty Cycle

VTHI

t^R, tF

InputTimingMeasurementReferenceLevel⁽³⁾

InputSignalEdgeRate⁽⁴⁾

CrossingPoint

V/ns

NOTES:

1. The 1V peak-to-peak input pulse level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VDIF (AC)

specification under actual use conditions.

2. A 900mV crossing point level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the V^Xspecification under

actual use conditions.

3. In all cases, input waveform timing is marked at the differential cross-point of the input signals.

4. The input signal edge rate of 2V/ns or greater is to be maintained in the 20% to 80% range of the input waveform.

DIFFERENTIAL INPUT AC TEST CONDITIONS FOR LVEPECL (2.5V) AND

LVPECL(3.3V)

Symbol

VDIF

Parameter

Value

Units

InputSignalSwing⁽¹⁾

732

DifferentialInputSignalCrossingPoint⁽²⁾

LVEPECL

LVPECL

1082

1880

Duty Cycle

VTHI

t^R, tF

InputTimingMeasurementReferenceLevel⁽³⁾

InputSignalEdgeRate⁽⁴⁾

CrossingPoint

V/ns

NOTES:

1. The 732mV peak-to-peak input pulse level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VDIF (AC)

specification under actual use conditions.

2. 1082mV LVEPECL (2.5V) and 1880mV LVPECL (3.3V) crossing point levels are specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment.

This device meets the VX specification under actual use conditions.

3. In all cases, input waveform timing is marked at the differential cross-point of the input signals.

4. The input signal edge rate of 2V/ns or greater is to be maintained in the 20% to 80% range of the input waveform.

IDT5T93GL02

2.5VLVDS1:2GLITCHLESSCLOCKBUFFERTERABUFFERII

INDUSTRIALTEMPERATURERANGE

DIFFERENTIAL INPUT AC TEST CONDITIONS FOR LVDS

Symbol

VDIF

Parameter

Value

Units

InputSignalSwing⁽¹⁾

DifferentialInputSignalCrossingPoint⁽²⁾

400

1.2

Duty Cycle

VTHI

t^R, tF

InputTimingMeasurementReferenceLevel⁽³⁾

InputSignalEdgeRate⁽⁴⁾

CrossingPoint

V/ns

NOTES:

1. The 400mV peak-to-peak input pulse level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the V^DIF(AC)

specification under actual use conditions.

2. A 1.2V crossing point level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the V^Xspecification under

actual use conditions.

3. In all cases, input waveform timing is marked at the differential cross-point of the input signals.

4. The input signal edge rate of 2V/ns or greater is to be maintained in the 20% to 80% range of the input waveform.

ACDIFFERENTIALINPUTSPECIFICATIONS⁽¹⁾

Symbol

VDIF

VIX

Parameter

Min.

0.1

Typ.

—

Max

3.6

Unit

ACDifferentialVoltage⁽²⁾

DifferentialInputCrosspointVoltage

CommonModeInputVoltageRange⁽³⁾

InputVoltage

0.05

- 0.3

—

VDD

+3.6

VCM

—

V^IN

NOTES:

1. The output will not change state until the inputs have crossed and the minimum differential voltage defined by V^DIFhas been met or exceeded.

2. VDIF specifies the minimum input voltage (VTR - VCP) required for switching where VTR is the "true" input level and VCP is the "complement" input level. The AC differential voltage

must be achieved to guarantee switching to a new state.

3. V^CMspecifies the maximum allowable range of (VTR + VCP) /2.

POWERSUPPLYCHARACTERISTICSFORLVDSOUTPUTS⁽¹⁾

Symbol

Parameter

Test Conditions

VDD = Max., All Input Clocks = LOW⁽²⁾

Outputsenabled

Typ.

Max

Unit

IDDQ

Quiescent VDD Power Supply Current

—

240

ITOT

IPD

Total Power VDD Supply Current

Total Power Down Supply Current

VDD = 2.7V., FREFERENCE CLOCK = 450MHz

PD = LOW

—

250

—

NOTES:

1. These power consumption characteristics are for all the valid input interfaces and cover the worst case conditions.

2. The true input is held LOW and the complementary input is held HIGH.

IDT5T93GL02

INDUSTRIALTEMPERATURERANGE

2.5VLVDS1:2GLITCHLESSCLOCKBUFFERTERABUFFERII

ACELECTRICALCHARACTERISTICSOVEROPERATINGRANGE^(1,5)

Symbol

Parameter

Min.

Typ.

Max

Unit

SkewParameters

tSK(O)

Same Device Output Pin-to-Pin Skew⁽²⁾

Pulse Skew⁽³⁾

—

tSK(P)

100

300

t^SK(PP)

Part-to-PartSkew⁽⁴⁾

PropagationDelay

t^PLH

tPHL

Propagation Delay A, A Crosspoint to Qn, Qn Crosspoint

—

1.5

2.2

FrequencyRange⁽⁶⁾

—

450

MHz

OutputGateEnable/DisableDelay

tPGE

Output Gate Enable Crossing VTHI to Qn/Qn Crosspoint

—

3.5

t^PGD

Output Gate Disable Crossing VTHI to Qn/Qn Crosspoint Driven to GL Designated Level

Power Down Timing

tPWRDN

PD Crossing VTHI to Qn = VDD, Qn = VDD

Output Gate Disable Crossing VTHI to Qn/Qn Driven to GL Designated Level

—

100

μS

t^PWRUP

NOTES:

1. AC propagation measurements should not be taken within the first 100 cycles of startup.

2. Skew measured between crosspoints of all differential output pairs under identical input and output interfaces, transitions and load conditions on any one device.

3. Skew measured is the difference between propagation delay times tPHL and tPLH of any single differential output pair under identical input and output interfaces, transitions and load

conditions on any one device.

4. Skew measured is the magnitude of the difference in propagation times between any single differential output pair of two devices, given identical transitions and load conditions

at identical V^DDlevels and temperature.

5. All parameters are tested with a 50% input duty cycle.

6. Guaranteed by design but not production tested.

IDT5T93GL02

2.5VLVDS1:2GLITCHLESSCLOCKBUFFERTERABUFFERII

INDUSTRIALTEMPERATURERANGE

DIFFERENTIALACTIMINGWAVEFORMS

1/fo

+ VDIF

VDIF = 0

- V^DIF

A[1:2] - A[1:2]

tPHL

tPLH

+ VDIF

VDIF = 0

- V^DIF

Qn - Qn

tSK(O)

+ VDIF

VDIF = 0

- V^DIF

Qm - Qm

Output Propagation and Skew Waveforms

NOTES:

1. Pulse skew is calculated using the following expression:

tSK(P) = | tPHL - tPLH |

Note that the tPHL and tPLH shown above are not valid measurements for this calculation because they are not taken from the same pulse.

2. AC propagation measurements should not be taken within the first 100 cycles of startup.

IDT5T93GL02

INDUSTRIALTEMPERATURERANGE

2.5VLVDS1:2GLITCHLESSCLOCKBUFFERTERABUFFERII

+ VDIF

VDIF = 0

- V^DIF

A[1:2] - A[1:2]

VIH

VTHI

VIL

tPLH

VIH

VTHI

VIL

tPGE

tPGD

+ VDIF

VDIF = 0

- V^DIF

Qn - Qn

Differential Gate Disable/Enable Showing Runt Pulse Generation

NOTE:

1. As shown, it is possible to generate runt pulses on gate disable and enable of the outputs. It is the user's responsibility to time the G signal to avoid this problem.

+ VDIF

VDIF = 0

- V^DIF

A1 - A1

A2 - A2

SEL

+ VDIF

VDIF = 0

- V^DIF

VIH

VTHI

VIL

+ VDIF

VDIF = 0

- V^DIF

Qn - Qn

Glitchless Output Operation with Switching Input Clock Selection

NOTES:

1. When SEL changes, the output clock goes LOW on the falling edge of the output clock up to three cycles later. The output then stays LOW for up to three clock cycles of the

new input clock. After this, the output starts with the rising edge of the new input clock.

2. AC propagation measurements should not be taken within the first 100 cycles of startup.

IDT5T93GL02

2.5VLVDS1:2GLITCHLESSCLOCKBUFFERTERABUFFERII

INDUSTRIALTEMPERATURERANGE

FSEL Operation for When Current Clock Dies

NOTES:

1. When the differential on the selected clock goes below the minimum DC differential, the outputs clock goes to an unknown state. When this happens, the SEL pin should be toggled

and FSEL asserted in order to force selection of the new input clock. The output clock will start up after a number of cycles of the newly-selected input clock.

2. The FSEL pin should stay asserted until the problem with the dead clock can be fixed in the system.

3. It is recommended that the FSEL be tied HIGH for systems that use only one input. If this is not possible, the user must guarantee that the unused input have a differential greater

than or equal to the minimum DC differential specified in the datasheet.

FSEL Operation for When Opposite Clock Dies

NOTES:

1. When the differential on the non-selected clock goes below the minimum DC differential, the outputs clock goes to an unknown state. When this happens, the FSEL pin should

be asserted in order to force selection of the new input clock. The output clock will start up after a number of cycles of the newly-selected input clock.

2. The FSEL pin should stay asserted until the problem with the dead clock can be fixed in the system.

3. It is recommended that the FSEL be tied HIGH for systems that use only one input. If this is not possible, the user must guarantee that the unused input have a differential greater

than or equal to the minimum DC differential specified in the datasheet.

IDT5T93GL02

INDUSTRIALTEMPERATURERANGE

2.5VLVDS1:2GLITCHLESSCLOCKBUFFERTERABUFFERII

+VDIF

VDIF=0

-V^DIF

A1 - A1

A2 - A2

FSEL

SEL

+VDIF

VDIF=0

-V^DIF

VIH

VTHI

VIL

VIH

VTHI

VIL

+VDIF

VDIF=0

-V^DIF

Qn - Qn

Selection of Input While Protecting Against When Opposite Clock Dies

NOTES:

1. If the user holds FSEL HIGH, the output will not be affected by the deselected input clock.

2. The output will immediately be driven to LOW once FSEL is asserted. This may cause glitching on the output. The output will restart with the input clock selected by the SEL

pin.

3. If the user decides to switch input clocks, the user must de-assert FSEL, then assert FSEL after toggling the SEL input pin. The output will be driven LOW and will restart with

the input clock selected by the SEL pin.

+VDIF

VDIF=0

-V^DIF

A1 - A1

A2 - A2

+VDIF

VDIF=0

-VDIF

VIH

VTHI

VIL

VIH

VTHI

VIL

+VDIF

VDIF=0

-V^DIF

Qn - Qn

Power Down Timing

NOTES:

1. It is recommended that outputs be disabled before entering power-down mode. It is also recommended that the outputs remain disabled until the device completes power-up after

asserting PD.

2. The POWER DOWN TIMING diagram assumes that GL is HIGH.

3. It should be noted that during power-down mode, the outputs are both pulled to VDD. In the POWER DOWN TIMING diagram this is shown when Qn - Qn goes to VDIF = 0.

IDT5T93GL02

2.5VLVDS1:2GLITCHLESSCLOCKBUFFERTERABUFFERII

INDUSTRIALTEMPERATURERANGE

TESTCIRCUITSANDCONDITIONS

~50Ω

Transmission Line

VIN

VDD/2

D.U.T.

Pulse

Generator

~50Ω

Transmission Line

VIN

-VDD/2

Scope

50Ω

Test Circuit for Differential Input

DIFFERENTIALINPUTTESTCONDITIONS

Symbol

VDD = 2.5V ± 0.2V

Unit

V^THI

Crossing of A and A

IDT5T93GL02

INDUSTRIALTEMPERATURERANGE

2.5VLVDS1:2GLITCHLESSCLOCKBUFFERTERABUFFERII

VDD

Pulse

Generator

D.U.T.

VOS

VOD

Test Circuit for DC Outputs and Power Down Tests

VDD/2

SCOPE

Z = 50Ω

Pulse

Generator

50Ω

D.U.T.

Z = 50Ω

C^L

-VDD/2

Test Circuit for Propagation, Skew, and Gate Enable/Disable Timing

LVDSOUTPUTTESTCONDITION

Symbol

VDD = 2.5V ± 0.2V

Unit

C^L

0⁽¹⁾

8^(1,2)

NOTES:

1. Specifications only apply to "Normal Operations" test condition. The TIA/EIA specification load is for reference only.

2. The scope inputs are assumed to have a 2pF load to ground. TIA/EIA - 644 specifies 5pF between the output pair. With CL = 8pF, this gives the test circuit appropriate 5pF equivalent

load.

IDT5T93GL02

2.5VLVDS1:2GLITCHLESSCLOCKBUFFERTERABUFFERII

INDUSTRIALTEMPERATURERANGE

ORDERINGINFORMATION

XXXXX

IDT

Package Process

Device Type

-40°C to +85°C (Industrial)

Thin Shrink Small Outline Package

TSSOP - Green

PGG

2.5V LVDS 1:2 Glitchless Clock Buffer

Terabuffer™ II

5T93GL02

CORPORATE HEADQUARTERS

for SALES:

for Tech Support:

6024 Silver Creek Valley Road

San Jose, CA 95138

800-345-7015 or 408-284-8200

fax: 408-284-2775

clockhelp@idt.com

www.idt.com

厂商	型号	描述	页数
IDT	5T9010BBGI8	[ PLL Based Clock Driver, 5T Series, 5 True Output(s), 0 Inverted Output(s), PBGA144, LEAD FREE, PLASTIC, BGA-144 ]	25 页
IDT	5T9050PGI	[ Low Skew Clock Driver, 5T Series, 5 True Output(s), 0 Inverted Output(s), CMOS, PDSO28, TSSOP-28 ]	7 页
IDT	5T905PGI	[ Low Skew Clock Driver, 5T Series, 5 True Output(s), 0 Inverted Output(s), CMOS, PDSO28, TSSOP-28 ]	17 页
IDT	5T9070PAGI8	[ Low Skew Clock Driver, 5T Series, 10 True Output(s), 0 Inverted Output(s), CMOS, PDSO48, GREEN, TSSOP-48 ]	9 页
IDT	5T9070PAI	[ Clock Driver, CMOS, PDSO48 ]	9 页
IDT	5T9070PAI8	[ Clock Driver, CMOS, PDSO48 ]	9 页
IDT	5T907PAI	[ Clock Driver, 5T Series, 10 True Output(s), 0 Inverted Output(s), CMOS, PDSO48, TSSOP-48 ]	19 页
IDT	5T907PAI8	[ Clock Driver, PDSO48 ]	19 页
IDT	5T9110BBGI8	[ PLL Based Clock Driver, 5T Series, 5 True Output(s), 0 Inverted Output(s), PBGA144, GREEN, PLASTIC, BGA-144 ]	23 页
IDT	5T915PAI	[ Clock Driver, CMOS, PDSO48 ]	19 页

购物指南

支付方式

配送服务

售后服务

发票须知

优惠券使用规则

特色服务

PCBA制造

国产品牌推荐

国产料号替代

质量保证

技术资料

行业资讯

关于我们

关于壹壹捌

联系我们

服务热线：400-618-9990

企业邮箱：sales@ic118.com

服务时间：周一至周六 8:30-17:30

壹壹捌官方微信号

PDF索引：

IC型号索引：

深圳网络警察报警平台

公共信息安全网络监察

经营性网站备案信息

不良信息举报中心

工商网监电子标识

全国公安机关备案

基本文件流程错误 SQL 调试用户

/www/wwwroot/www.ic72.com/public/index.php ( 0.79 KB )
/www/wwwroot/www.ic72.com/vendor/autoload.php ( 0.73 KB )
/www/wwwroot/www.ic72.com/vendor/composer/autoload_real.php ( 1.63 KB )
/www/wwwroot/www.ic72.com/vendor/composer/platform_check.php ( 1.01 KB )
/www/wwwroot/www.ic72.com/vendor/composer/ClassLoader.php ( 15.99 KB )
/www/wwwroot/www.ic72.com/vendor/composer/autoload_static.php ( 12.68 KB )
/www/wwwroot/www.ic72.com/vendor/ralouphie/getallheaders/src/getallheaders.php ( 1.60 KB )
/www/wwwroot/www.ic72.com/vendor/symfony/deprecation-contracts/function.php ( 0.99 KB )
/www/wwwroot/www.ic72.com/vendor/guzzlehttp/guzzle/src/functions_include.php ( 0.16 KB )
/www/wwwroot/www.ic72.com/vendor/guzzlehttp/guzzle/src/functions.php ( 5.55 KB )
/www/wwwroot/www.ic72.com/vendor/adbario/php-dot-notation/src/helpers.php ( 0.57 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-helper/src/helper.php ( 8.34 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/stubs/load_stubs.php ( 0.16 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/Exception.php ( 1.69 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/Facade.php ( 2.71 KB )
/www/wwwroot/www.ic72.com/vendor/yansongda/supports/src/Functions.php ( 1.53 KB )
/www/wwwroot/www.ic72.com/vendor/hyperf/engine/src/Functions.php ( 0.83 KB )
/www/wwwroot/www.ic72.com/vendor/symfony/polyfill-mbstring/bootstrap.php ( 8.26 KB )
/www/wwwroot/www.ic72.com/vendor/symfony/polyfill-mbstring/bootstrap80.php ( 9.77 KB )
/www/wwwroot/www.ic72.com/vendor/yansongda/artful/src/Functions.php ( 2.38 KB )
/www/wwwroot/www.ic72.com/vendor/phpseclib/phpseclib/phpseclib/bootstrap.php ( 0.72 KB )
/www/wwwroot/www.ic72.com/vendor/symfony/var-dumper/Resources/functions/dump.php ( 1.49 KB )
/www/wwwroot/www.ic72.com/vendor/yansongda/pay/src/Functions.php ( 19.32 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/App.php ( 14.29 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/Container.php ( 15.39 KB )
/www/wwwroot/www.ic72.com/vendor/psr/container/src/ContainerInterface.php ( 1.02 KB )
/www/wwwroot/www.ic72.com/app/provider.php ( 0.19 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/Http.php ( 6.04 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-helper/src/helper/Str.php ( 7.29 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/Env.php ( 4.52 KB )
/www/wwwroot/www.ic72.com/app/common.php ( 105.26 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/helper.php ( 18.47 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/Config.php ( 4.62 KB )
/www/wwwroot/www.ic72.com/config/api.php ( 0.59 KB )
/www/wwwroot/www.ic72.com/config/app.php ( 2.94 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/facade/Env.php ( 1.67 KB )
/www/wwwroot/www.ic72.com/config/cache.php ( 1.07 KB )
/www/wwwroot/www.ic72.com/config/console.php ( 0.23 KB )
/www/wwwroot/www.ic72.com/config/cookie.php ( 2.06 KB )
/www/wwwroot/www.ic72.com/config/database.php ( 5.02 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/facade/Config.php ( 1.37 KB )
/www/wwwroot/www.ic72.com/config/email.php ( 2.34 KB )
/www/wwwroot/www.ic72.com/config/filesystem.php ( 0.68 KB )
/www/wwwroot/www.ic72.com/config/lang.php ( 0.82 KB )
/www/wwwroot/www.ic72.com/config/log.php ( 1.35 KB )
/www/wwwroot/www.ic72.com/config/middleware.php ( 0.19 KB )
/www/wwwroot/www.ic72.com/config/payment.php ( 0.00 KB )
/www/wwwroot/www.ic72.com/config/route.php ( 1.54 KB )
/www/wwwroot/www.ic72.com/config/session.php ( 0.70 KB )
/www/wwwroot/www.ic72.com/config/trace.php ( 0.58 KB )
/www/wwwroot/www.ic72.com/config/view.php ( 0.96 KB )
/www/wwwroot/www.ic72.com/app/event.php ( 0.26 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/Event.php ( 6.97 KB )
/www/wwwroot/www.ic72.com/app/service.php ( 0.13 KB )
/www/wwwroot/www.ic72.com/app/AppService.php ( 0.26 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/Service.php ( 1.64 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/Lang.php ( 7.22 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/lang/zh-cn.php ( 13.27 KB )
/www/wwwroot/www.ic72.com/app/lang/zh-cn.php ( 0.08 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/initializer/Error.php ( 3.27 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/initializer/RegisterService.php ( 1.33 KB )
/www/wwwroot/www.ic72.com/vendor/services.php ( 0.18 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/service/PaginatorService.php ( 1.52 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/service/ValidateService.php ( 0.99 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/service/ModelService.php ( 1.75 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-multi-app/src/Service.php ( 1.08 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-trace/src/Service.php ( 0.77 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/Middleware.php ( 6.65 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/initializer/BootService.php ( 0.77 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/src/Paginator.php ( 11.71 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/Validate.php ( 46.61 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/src/Model.php ( 26.86 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/src/model/concern/Attribute.php ( 19.12 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/src/model/concern/RelationShip.php ( 26.44 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/src/model/concern/ModelEvent.php ( 2.58 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/src/model/concern/TimeStamp.php ( 5.69 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/src/model/concern/AutoWriteId.php ( 1.44 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/src/model/concern/Conversion.php ( 10.85 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-helper/src/contract/Arrayable.php ( 0.09 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-helper/src/contract/Jsonable.php ( 0.13 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/Db.php ( 2.88 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/src/DbManager.php ( 8.33 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/Log.php ( 6.27 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/Manager.php ( 3.92 KB )
/www/wwwroot/www.ic72.com/vendor/psr/log/src/LoggerTrait.php ( 2.69 KB )
/www/wwwroot/www.ic72.com/vendor/psr/log/src/LoggerInterface.php ( 2.68 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/Cache.php ( 4.91 KB )
/www/wwwroot/www.ic72.com/vendor/psr/simple-cache/src/CacheInterface.php ( 4.71 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-helper/src/helper/Arr.php ( 16.08 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/cache/driver/File.php ( 7.60 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/cache/Driver.php ( 8.17 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/contract/CacheHandlerInterface.php ( 1.99 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/Console.php ( 22.64 KB )
/www/wwwroot/www.ic72.com/app/Request.php ( 0.09 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/Request.php ( 54.27 KB )
/www/wwwroot/www.ic72.com/app/middleware.php ( 0.26 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/Pipeline.php ( 2.61 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-trace/src/TraceDebug.php ( 2.94 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-multi-app/src/MultiApp.php ( 7.06 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/Route.php ( 23.25 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/route/RuleName.php ( 5.31 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/route/Domain.php ( 5.53 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/route/RuleGroup.php ( 13.56 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/route/Rule.php ( 23.18 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/route/RuleItem.php ( 9.19 KB )
/www/wwwroot/www.ic72.com/route/app.php ( 0.77 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/facade/Route.php ( 4.68 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/route/dispatch/Url.php ( 3.42 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/route/dispatch/Controller.php ( 6.61 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/route/Dispatch.php ( 6.07 KB )
/www/wwwroot/www.ic72.com/app/controller/Pdf.php ( 21.90 KB )
/www/wwwroot/www.ic72.com/app/controller/Api.php ( 11.17 KB )
/www/wwwroot/www.ic72.com/app/BaseController.php ( 2.04 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/facade/Cookie.php ( 1.48 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/Cookie.php ( 5.97 KB )
/www/wwwroot/www.ic72.com/app/model/Type.php ( 0.45 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/src/db/connector/Mysql.php ( 4.33 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/src/db/PDOConnection.php ( 51.60 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/src/db/Connection.php ( 8.79 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/src/db/ConnectionInterface.php ( 4.86 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/src/db/builder/Mysql.php ( 16.56 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/src/db/Builder.php ( 22.26 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/src/db/BaseBuilder.php ( 27.29 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/src/db/Query.php ( 15.19 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/src/db/BaseQuery.php ( 41.48 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/src/db/concern/TimeFieldQuery.php ( 7.43 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/src/db/concern/AggregateQuery.php ( 3.26 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/src/db/concern/ModelRelationQuery.php ( 19.29 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/src/db/concern/ParamsBind.php ( 3.66 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/src/db/concern/ResultOperation.php ( 6.98 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/src/db/concern/Transaction.php ( 2.77 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/src/db/concern/WhereQuery.php ( 18.79 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/src/db/concern/JoinAndViewQuery.php ( 6.96 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/src/db/concern/TableFieldInfo.php ( 2.46 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/log/driver/File.php ( 6.17 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/contract/LogHandlerInterface.php ( 0.86 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/log/Channel.php ( 3.88 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/event/LogRecord.php ( 0.86 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/src/model/Collection.php ( 6.96 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-helper/src/Collection.php ( 16.48 KB )
/www/wwwroot/www.ic72.com/app/model/Cart.php ( 15.85 KB )
/www/wwwroot/www.ic72.com/app/model/Api.php ( 11.18 KB )
/www/wwwroot/www.ic72.com/app/controller/Index.php ( 25.20 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-orm/src/facade/Db.php ( 0.93 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/facade/View.php ( 1.70 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/View.php ( 4.33 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-view/src/Think.php ( 8.00 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-template/src/Template.php ( 46.61 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-template/src/template/driver/File.php ( 2.41 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-template/src/template/contract/DriverInterface.php ( 0.86 KB )
/www/wwwroot/www.ic72.com/runtime/temp/74795295d09f215cb811aa199c120a8d.php ( 39.52 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/Response.php ( 8.65 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/framework/src/think/response/Html.php ( 0.97 KB )
/www/wwwroot/www.ic72.com/vendor/topthink/think-trace/src/Html.php ( 4.49 KB )